Jensen JCD3006 Manuel d'utilisateur Page 9

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 10
  • Table des matières
  • DEPANNAGE
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 8
JCD3006
9
SPECIFICATIONS
CD
Signal to Noise Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >
70dB
Sampling Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.1Khz
Quantization Bits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 bit
Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . 5-20,000Hz
Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Channel (Stereo)
FM Radio
Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87.5-107.9MHz
Intermediate Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.7MHz
Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >
15dB at S/N 30dB
Stereo Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25dB at 1KHz
S/N Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50dB
AM/MW
Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530-1710KHz
Intermediate Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .450KHz
Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >
45dB
S/N Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40dB
General
Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC 11 -14.4
Grounding System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Negative Ground
Speaker Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ohms
Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40W x 4
TROUBLESHOOTING
Symptom Cause Solution
No power The vehicle’s ignition is not
on
If the power supply is properly
connected to the vehicle acces-
sory terminal, switch the ignition
key to “ACC”.
The fuse is blown Replace the fuse.
Disc cannot be loaded or
ejected
Presence of CD disc inside
the player
Remove the disc in the player and
insert the new one.
Inserting the disc in reverse
direction
Insert the compact disc with the
label facing upward.
Compact disc is extremely
dirty or disc is defective
Clean the disc or try to play a new
one.
Temperature inside the
vehicle is too high
Wait until the ambient tempera-
ture returns to normal.
Condensation Leave the player off for an hour or
so, then try again.
No sound Volume is too low Adjust volume to audible level.
Wiring is not properly con-
nected.
Check wiring connections.
The operation keys do
not work
Control panel not properly
installed
Reinstall control panel.
The built-in microcomputer
is not operating properly
due to noise
Press the RESET button.
Sound skips The installation angle is
more than 30 degrees.
Adjust the installation angle to
less than 30 degrees.
The disc is dirty or defec-
tive.
Clean the disc and try to play
again or use new disc.
Cannot tune to radio sta-
tion, auto-seek does not
work
The antenna cable is not
connected.
Insert the antenna cable firmly.
The signals are too weak. Select a station manually.
ERROR 1 Mechanism Error Press the eject button to correct
the problem.
If the error code does not disap-
pear, consult your nearest ser-
vice dealer.
ERROR 2 Servo Error Press the eject button to correct
the problem.
If the error code does not disap-
pear, consult your nearest ser-
vice dealer.
Vue de la page 8
1 2 3 4 5 6 7 8 9 10

Commentaires sur ces manuels

Pas de commentaire